Update Module for Harmonics Explorer
- This is the latest update module for the “Harmonics Explorer”.
- To use this module, you will also need to upgrade the KHA1000 main unit.
- In order to install this module, the full version of SD005-KHA Harmonics Explore must already be installed.
- Please be aware that this software is not compatible with Windows XP and previous operating systems.
Ver.
4.0.0
Last update
2026/09/04
Configuration
- Windows 11
Download
Release Notes
VER 4.0.0
2026-09-04
HarmoCapture / HA File Analyzer
-
New Feature
Added support for the harmonic current limit standard IEC 61000-3-2 Ed5.2 with the following features. (Supports the KHA1000 with versions 2.11 and later.)
- Updated IEC Ed5.2/Ed2.1 or IEC Ed5.2/Ed1.0 report text: standard name set to “IEC61000-3-2 Ed5.2” and alias set to “EN IEC 61000-3-2(2019)/A2(2024).”
- Changed the current values printed on reports for IEC Ed5.2/Ed2.1 and IEC Ed5.2/Ed1.0 to the average values during the test period. (The maximum values during the test period were printed on reports for Ed5.0.)
- Changed the POHC values printed on reports for IEC Ed5.2/Ed2.1 and IEC Ed5.2/Ed1.0 to the average values during the test period. (The maximum values during the test period were printed on reports for Ed5.0.) Also added a supplementary explanation about the POHC calculation method at the bottom of the page.
HarmoCapture / Vf File Analyzer
-
New Feature
Added support for the flicker limit standard IEC 61000-3-3 Ed3.2 with the following features. (Supports the KHA1000 with versions 2.11 and later.)
- Updated IEC61000-3-3 Ed3.2 report text: standard name set to “IEC61000-3-3 Ed3.2” and alias set to “EN61000-3-3(2013)/A2(2021).”
- Retained support for loading IEC61000-3-3 Ed3.1 test results files.
HarmoCapture
- Improvement Discontinued tests for harmonic limit standard IEC61000-3-2 Ed5.0. Enabled tests for IEC61000-3-2 Ed5.2 instead.
- Improvement Discontinued tests for flicker limit standard IEC61000-3-3 Ed3.1. Enabled tests for IEC61000-3-3 Ed3.2 instead.
- Improvement Changed the feature name “Simulation Mode” to “Offline Mode”
- Improvement Changed to display a prompt for an update if a KHA1000 with an outdated version is connected.
- Resolved issues Resolved an issue that caused error messages to appear repeatedly when the KHA1000 was disconnected during monitoring.
- Resolved issues Resolved an issue where the standard conditions settings would differ from those of the KHA1000 upon starting the HarmoCapture.
- Resolved issues Resolved an issue where the KHA1000 settings could not be retrieved unless the settings were sent with a measurement time of “0 minutes.”
HA File Analyzer
-
New Feature
Updated the threshold values used for “repeatability check” on IEC Ed5.2/Ed2.1 and IEC Ed5.2/Ed1.0 as follows:
11th order or lower: The average harmonic current being compared must be within ±(5% of the limit value + 1 mA).
12th order or higher: The average harmonic current being compared must be within ±(10% of the limit value + 1 mA). - New Feature Applied positive and negative peak voltage judgment (i.e., crest factor judgment) to Classes A and B in “Checking the AC power Source” when IEC Ed5.2/Ed2.1 or IEC Ed5.2/Ed1.0 was selected.
Vf File Analyzer
- Resolved issues Corrected the printing of the flicker limit standard to “IEC61000-3-3 Ed2.0” in reports generated from the test results of the flicker measurement technical standard IEC61000-4-15 Ed1.1.
Ver 3.9.2 or earlier
VER 3.9.2
2024-11-27
HarmoCapture
- Resolved issues Fixed the issue where a set specification is not applied even after pressing the "send" button when a JIS2019/Ed2.1 setting file is opened.
- Resolved issues Fixed the issue where the AC power supply control panel is hidden when HarmoCapture is enabled while its window size is maximized.
VER 3.9.1
2023-07-04
HarmoCapture / HA File Analyzer
- Resolved issues The description of the standard for measurement techniques that conforms to JIS C61000-3-2(2019) has been revised from JIS C61000-4-7(2007) to IEC61000-4-7 Ed2.1(2009).
VER 3.9.0
2021-11-26
HarmoCapture / HA File Analyzer / Vf File Analyzer
- New Feature IEC61000-3-2 Ed4.0 of HA limitation standard was changed to IEC61000-3-2 Ed5.0.
- New Feature JIS C 61000-3-2 2011 of HA limitation standard was changed to JIS C 61000-3-2 2019.
- New Feature IEC61000-3-3 Ed3.0 of Vf flicker limitation standard was changed to IEC61000-3-3 Ed3.1.
VER 3.8.0
2021-04-08
HarmoCapture / Vf File Analyzer
- New Feature This version operates also in AC power supply PCR-WEA series.
- Resolved issues There was a problem whose output ON/OFF of AC power supply in the instrument menu was not effective.
- Resolved issues The front name of radio buttons in voltage range of AC power supply has been replaced Low-High from 100V-200V.
- Resolved issues While not opening the result file by Vf File Analyzer, there was a problem to which an exception error occurs, when Segment information was clicked.
VER3.7.1
2018-5-10
Vf File Analyzer
- Resolved issues When IEC61000-4-15 is Ed2.0, IEC61000-3-3 is Ed3.0. However, 3-3 Ed2.0 was a mistake.
VER 3.7.0
2017-5-26
HarmoCapture / HA File Analyzer / Vf File Analyzer
- Resolved issues For HA limitation standards, "IEC61000-3-2 Ed4.0" have been added.
- Resolved issues For Flicker limitation standards, "IEC61000-3-3 Ed3.0" have been added.
VER 3.6.5
2016-9-2
HarmoCapture
- Resolved issues There was a problem which the voltage range of PCR-LE could not change. This problem occured only in Ver3.6.4
VER 3.6.4
2016-4-5
HarmoCapture
- Resolved issues There was a problem which does not conform to IEC61000-4-15 Ed2.0. The steady state and d measurement algorithm were changed.
VER 3.6.3
2015-2-3
HA File Analyzer
- Resolved issues There was a problem which had not been taking the magnification of a current range into consideration by text conversion of a V/I waveform.
VER 3.6.2
2014-9-2
HarmoCapture
- Resolved issues There was a problem that the suitable value had not been shown in dialog of "Check the line impedance".
- Resolved issues When Key input to a NumericUpDown control, there was a problem that nominal voltage and frequency had returned to a former setup at click of Send-button.
- Resolved issues Change to read setting value from KHA at the time of the first HA-Vf change after boot of HarmoCapture.
VER 3.6.1
2014-7-1
Vf File Analyzer
- Resolved issues Vf File Analyzer Ver3.6.0 had a problem which could not read a result file created by KHA1000 Ver1.73 or earlier.
VER 3.6.0
2013-12-6
HarmoCapture
- New Feature For HA limitation standards "JIS C 61000-3-2 2011" have been added.
- Improvement Measurement time was extended to 9600 seconds.
- New Feature Corresponded to remote control of LIN-JF series.
VER 3.5.5
2012-9-14
HarmoCapture
- New Feature AC power supply PCR-LE series have been added to the operation.
VER 3.5.4
2011-10-18
HarmoCapture
- Resolved issues There was a problem that send progress bar was not zero clear even if changed radio button of flicker measurement technic "IEC61000-4-15 Ed1.1" and "IEC61000-4-15 Ed2.0".
VER 3.5.3
2011-5-16
HarmoCapture / HA File Analyzer / Vf File Analyzer
- Improvement English contents and user's manual was updated.
- Improvement English contents and user's manual was updated.
- Improvement English contents and user's manual was updated.
VER 3.5.2
2011-2-21
HarmoCapture
- Resolved issues When operated HA -> Vf -> HA, there was a problem which the standard group name had changed to "Standard 61000-3-3 / 4-15".
VER 3.5.1
2011-1-25
HarmoCapture
- Resolved issues When setting files except JIS2005 were opened, there was a problem which an error occurs.
- Resolved issues For Flicker measurement technic "IEC61000-4-15 Ed1.1" and "IEC61000-4-15 Ed2.0" can be saved now in vs file.
- Resolved issues When a hs file before Ver3.4.5 was read, there was a problem which a standard changes.
VER 3.5.0
2010-12-16
HarmoCapture / HA File Analyzer / Vf File Analyzer
- Improvement For HA limitation standards, "IEC61000-3-2 Ed3.0 A2" and measurement technic "IEC61000-4-7 Ed2.0 A1" have been added.
- New Feature Reference impedance is now selectable to "Use" or "Un-use" when JIS2005 selected.
- Improvement For Flicker limitation standards, "IEC61000-3-3 Ed2.0" and measurement technic "IEC61000-4-15 Ed2.0" have been added.
- New Feature Confirmation of AC power source have been added. This is applied to screen display and reports.
- Improvement Only when HA limitation standard selected IEC61000-3-2 Ed3.0 A2, calculation denominator of a repeatability is the limit value. Less than 5% is Pass.
- New Feature Alias Standard of measurement technic for Ed1.1 and Ed2.0 are added.
VER 3.4.5
2010-9-15
HarmoCapture / HA File Analyzer / Vf File Analyzer
- New Feature IEC61000-3-2 Ed3.0 A2 / 61000-4-7 Ed2.0 A1 and IEC61000-3-2 Ed3.0 A2 / 61000-4-7 Ed1.0 have been added to HA. By this addition, the latest standards and other standards are now put into the radio-buttons and a combox respectively.
- New Feature Only when Class C is selected under IEC Ed3.0A2 / Ed2.0A1 or IEC Ed3.0A2 / Ed1.0, 3rd/5th/current-waveform are now displayed at applied limitation values.
- Improvement The standard selection IEC Ed1.2/Ed1.1 is changed to IEC Ed2.0/Ed1.1 for Vf.
- New Feature A description figure of current waveform requirement is now drawn at V/I waveform when a result file where the applied limit values are 3rd/5th/current-waveform in Class-C. This is applied to screen display and reports.
- New Feature Because "Use Alias Standard" and related items are added, an arbitrary standard name is now able to print in reports.
- New Feature The 2D harmonic current auto-scale is now selectable to "Meas Value" or "Meas and Limit". In "Meas and Limit", the appropriate scale is calculated from measurement values and limit values, therefore the printing problem that the limit values were too high to print has been fixed.
- New Feature Because "Use Alias Standard" and related items are added, an arbitrary standard name is now able to print in reports.
VER 3.4.4
2009-12-3
HarmoCapture
- Resolved issues There was a problem that the final judgement on report could be FAIL in spite of test result passed.
VER 3.4.3
2009-10-15
HarmoCapture / HA File Analyzer
- Improvement The setting screen is now greyed out while testing so that parameter settings cannot be altered.
- Resolved issues There was a problem that the max apparent power value in the report was shown as the max value during test period.
VER 3.4.2
2009-7-10
HarmoCapture / HA File Analyzer / Vf File Analyzer
- Improvement There was a problem that test reports under IEC61000-3-2 Ed3.0 incorrectly indicated Limit Over(s) values even if other than Class A.
- Improvement At IEC61000-3-3 manual switching d-measurement, there was a problem that the remaining time display was extremely wrong when starting the test without sending test condition after the previous measurement was once finished.
- Improvement There was a problem that the file size of report pdf could be extemely big. It has no side effect on printout itself.
- Improvement There was a problem that the V/I waveform printouts indicated fixed 0A values when the current was minimal such as when +Peak is 0A and -Peak is 0.05A.
- Improvement There was a problem that test reports under IEC61000-3-2 Ed3.0 incorrectly indicated Limit Over(s) values even if other than Class A.
- Improvement When testing at other than 230V/50Hz, the report incorrectly printed out EN standard name in spite of the specification not printing it.
- Improvement There was a problem that the "*3" and "*4" remarks on the IEC61000-3-2 Ed3.0 report could be incorrecly shown by the side effect of previous test.
- Improvement At the Vf Report Voltage Fluctuation graphs, there was a problem that the arrows indicating the start-point of dc, dmax, and dt, could not be printed out.
VER 3.4.1
HarmoCapture / HA File Analyzer / VF File Analyzer
- Resolved issues Corrected a typo found in generated reports (Fluction → Fluctuation).
- Resolved issues There was a problem that report pdf could be unnecesarily huge.
VER 3.4.0
2008-11-21
HA File Analyzer / VF File Analyzer
- Improvement Footer option has been added to the report functionality.
VER 3.3.1
2008-6-20
HarmoCapture / HA File Analyzer / Vf File Analyzer
- Improvement For HA test standards, "IEC61000-3-2 Ed3.0/4-7 Ed2.0" and "IEC61000-3-2 Ed3.0/4-7 Ed1.0" have been added.
- Improvement The "Limit Over" item has been added to test reports of "IEC61000-3-2 Ed3.0".
- Improvement The Vf test standard "IEC61000-3-3 Ed1.1" has been changed to "Ed1.2".
- Improvement When send operation finished, a message "Send was completed" is now displayed beneath the send progress bar.
- Improvement A message "remaining time" is now displayed beneath the test progress bar.
- Improvement For the test progress bar at Vf Manual Switching operation, it now represents 100% for each segment. Furthermore, "Segment (measuring)/(total)" is now displayed.
- Improvement At Vf Manual Switching, a dialogue box prompt is now shown when you wait for the next measurement, in order to increase visiblity.
- Improvement It is now compatibe with the added standard "IEC61000-3-2 Ed3.0"
- Improvement The flicker list view has been added. Furthermore the flicker list page is also added to reports.
VER 3.2.1.2
2008-4-11
VF File Analyzer
- Resolved issues In Vf reports of Pst Auto Switching mode, measurement time and count of Manual Switching were incorrectly used.
VER 3.2.1
2008-3-27
HarmoCapture / VF File Analyzer
- Improvement Limitation judgement (Judge Factor) are now selectable from pst, plt, dc, dmax, and d(t)>3.3%.
VER 3.1.0
2007-7-23
HarmoCapture / HA File Analyzer / VF File Analyzer
- Improvement As the item name "Comment" on the menu and toolbars is not comprehensive, it has been changed to "Report Setting".
- Resolved issues When openning a result file captured under Class-C by using KHA1000 mains VER1.20 or earlier versions, there were errors on current values. (This fault is found on V/I current waveform graph only.)
- Improvement As the item name "Comment" on the menu and toolbars is not comprehensive, it has been changed to "Report Setting".
- Improvement 2D Harmonics Graph is now printable on the report.
- Improvement V/I Waveform Graph is now printable on the report.
- Improvement Harmonic Trend Graph is now printable on the report.
- Improvement Current Trend Graph is now printable on the report.
- Improvement THC Trend Graph is now printable on the report.
- Improvement Setting List is now printable on the report.
- Improvement Repeatability confirmation list is now printable on the report.
- Improvement As the item name "Comment" on the menu and toolbars is not comprehensive, it has been changed to "Report Setting".
- Improvement Voltage Fluctuation Graph of the selected segment is now printable on the report.
- Improvement Zoom-In graph on 'dc' is now printable on the report.
- Improvement Zoom-In graph on 'dmax' is now printable on the report.
- Improvement Zoom-In graph on 'd(t)>3.3%' is now printable on the report.
- Improvement Segment Information list is now printable on the report.
- Improvement Setting List is now printable on the report.
VER 3.0.0
2007-4-13
HarmoCapture / HA File Analyzer / VF File Analyzer
- Improvement An overwrite prompt dialog has been added when generating PDF files.
- Improvement Now compatible with the high-precision updagade of the KHA1000 mains.
- Resolved issues There was a problem that num of frames and their time slice are mismatched on Trend Graph's test time.
- Resolved issues There was a pronlem that the red and yellow colouring of 2D harmonic bar-graphs was incorrect.
- Resolved issues There was a problem that the display of [Ignore]/[Not Ignore] options was incorrectly reversed.
- Improvement Decimal display formats for Over-100% and Over-Margin have been changed so that they now match with the KHA1000 mains.
- Improvement Separator format for text save is now selectable.
- Improvement An overwrite prompt dialog has been added when generating PDF or text files.
- Improvement Now compatible with the high-precision updagade of the KHA1000 mains.
- New Feature This application is newly added.
VER 2.0.0
2006-11-06
HarmoCapture / HA File Analyzer
- Resolved issues There was a probem that PCs equiping OHCI USB host and any Windows2000 environment could not acquire measurement data through the USB interface.
- Resolved issues There was a problem that PCR-L could not be controlled.
- Improvement Upon report printing, it now prints the result file of the test immediately before. The functionality to print an arbitrary file has been moved to [File]->[Select file and print report...] menu.
- Improvement Upon class selection, "61000-3-2/4-7 IEC Ed2.2/Ed1.0", and "61000-3-2/4-7 JIS 2005/Ed1.0" have been added.
- New Feature This application is newly added.
VER 1.0.0
2006-3-22
HarmoCapture
- New Feature The first release
