| PFX2512 | PFX2532 | ||
|---|---|---|---|
| Nominal input rating | 100 Vac to 240 Vac, 50 Hz/60 Hz | ||
| Input voltage range | 90 Vac to 250 Vac | ||
| Power consumption | 60 VAmax (when three OP02-PFXs are installed: 80 VAmax) | ||
| Operating temperature and humidity range | 0 °C to 40 °C (32 °F to 104 °F), 20 %rh to 85 %rh (no condensation) | ||
| Storage temperature and humidity range | -10 °C to 60 °C (14 °F to 140 °F), 0 %rh to 90 %rh (no condensation) | ||
| Operating environment | Indoors, overvoltage category II | ||
| Altitude | Up to 2000 m | ||
| Isolation voltage | Between I/O terminals and chassis | ± 60 Vmax | ± 60 Vmax |
| Insulation resistance *4 | Between primary and chassis | 500 Vdc, 30 MΩ or greater, 70 %rh humidity or less | |
| Primary and across the I/O terminals | |||
| Withstanding voltage | Between primary and chassis | No abnormalities at 1500 Vac for 1 minute | |
| Primary and across the I/O terminals | |||
| Safety *1 | Complies with the require- ments of the following directive and standard. Low Voltage Directive 2014/35/EU *2 EN61010-1 (Class I *3, Pol- lution degree 2 *4) | ||
| Electromagnetic compatibility *1 *2 | Complies with the require- ments of the following directive and standard. EMC Directive 2014/30/EU EN61326-1 (Class A *5) EN55011 (Class A *5, Group 1 *6) EN61000-3-2, EN61000-3-3 | ||
| Applicable under the following conditions. The maximum length of all cabling and wiring connected to the PFX2512 is less than 5 m. | Applicable under the following conditions. The maximum length of all cabling and wiring connected to the PFX2532 is less than 3 m. | ||
| Dimensions | See the outline drawing | ||
| Weight | Approx. 7 kg (15.43 lb) | Approx. 17 kg (37.48 Ib) | |
| Accessories | Power cord *7 | 1 pc | 1 pc |
| Cable with Solderless terminal | 4 pcs (Red: 2 pcs, White: 2 pcs) 45 cm each (17.72 inch) | − | |
| I/O terminal cover set | − | Three terminal covers, six cable ties for locking | |
| I/O terminal M8 screw set | − | 6 sets | |
| Load input terminal cover set | − | Cover, four auxiliary bands | |
| 26-core flat cable | 1 pc | 1 pc | |
| 20-core flat cable | 1 pc | 1 pc | |
| 26-core cable (with ferrite core) | − | 1 pc | |
| Sensing connector | 1 pc | 1 pc | |
| Sensing connector cover set | − | One cover set, one cable tie for locking | |
| Thermistor | 1 pc | 1 pc | |
| Lock lever | 2 pcs | 2 pcs | |
| LAN cable | 1 pc. Straight type | 1 pc. Straight type | |
| Operation Manuals | 1 copy | 1 copy | |
*1 DoesnotapplytospeciallyorderedormodifiedPFX2512sandPFX2532s. *2 Limited to products that have the CE/UKCA mark on their panels. When the optional OP03-PFX Voltmeter Unit is used, compliance is achieve by using the optional TL12-PFX sensing cable (length: approx. 3 m, connector area: with cover, with core). *3 ThisisaClassIequipment.BesuretogroundthePFX2512’sandPFX2532’sprotectiveconduc- tor terminal. The safety of this product is only guaranteed when the product is properly grounded. *4 Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or surface resistivity. Pollution Degree 2 assumes that only non-conductive pol- lution will occur except for an occasional temporary conductivity caused by condensation. *5 This is a Class A equipment. The PFX2512 and PFX2532 is intended for use in an industrial environment. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts. *6 This is a Group 1 equipment. The PFX2512 and PFX2532 does not generate and/or use intention- ally radio-frequency energy, in the from of electromagnetic radiation, inductive and/or capacitive coupling, for the treatment of material or inspection/analysis purpose. *7 Because the power cord does not comply with CE/UKCA, it may not be included depending on the shipment destination.
